Product Search
Search results for 'T-217'
Showing 241 - 260 of 1123 Total Results
(6) options
Location: Scoops
Test Mark supplies a variety of round mouth and flat bottom scoops for use in the construction materials testing industry.
SA-1302
Location: Probe Rod
For protection against possible electrical shock when working around buried electrical lines. T-handle has high density nylon cover. Shaft is 1/2" dia. x 48" long, steel tip measures 5/8" x 3/4". NOTE : Because size and weight will vary with quantities ordered, we have reserved the freight charges...
(5) options
Location: Unit Weight Buckets
Aluminum cylindrical unit weight measures from Test Mark have machined interior surfaces, carrying handles, true and even top and bottom surfaces, are water-tight and will retain form after repeated use.
Asphalt Dispenser, 4 Qt. (3.8 L)
AA-3000
Location: Asphalt Dispenser
Asphalt Dispenser features a round melting pot has stainless steel crucible & shell to facilitate easy clean up - from Test Mark Industries.
(4) options
Location: Crack Monitors
Concrete crack monitors from Test Mark are simple, accurate devices for monitoring crack movement.
Indicating Drierite, 1 lb., Blue
AA-0122
Location: Drierite
Blue dessicant turns red to show absorption and may be reused. One of our Drierite products.
Hardware Kit, 4 knobs with screws
CA-0340-03
Location: Plastic Beam Molds
Extra hardware kit for Plastic Beam Molds.
Stainless Steel Clamp Assembly
CA-0600-07P
Location: Parts & Accessories
Stainless steel clamp assembly. Plastic Roll-A-Meter Kit replacement parts.
CA-0217
Location: Cylinder Transport
The steel concrete cylinder carrier from Test Mark is used for carrying 6-inch dia. cylinders in the field or lab.
AA-0040
Location: Marshall Hand Compaction Hammer
The Hand Compaction Hammer set from Test Mark Industries facilitates hand compaction of 4-inch samples.
MA-0802
Location: Draw Rod Assembly
Safer, easier and faster changing of test platens and spacers. . The draw rod system is used to adjust the inside vertical working height of the load frame, to allow for testing samples of different heights through the use of spacers and test platens. The system is made up of a steel hand wheel...
Drive Tubes, 3" x 2.75" (76.2 x 69.9 mm), 10/pkg
SA-1371
Location: Density Drive Sampler
For use with Drive Sampler, 3" (76.2mm) x 2.75" (69.9mm) length, (3" x 0.01 ft3). Accessory to the density drive sampler.
Drive Tubes, 4" x 5.00" (101.6 x 127 mm), 10/pkg
SA-1372
Location: Density Drive Sampler
For use with Drive Sampler, 4" (101.6mm) x 5" (127mm) length, (4" x 0.033 ft3).
(6) options
Location: Concrete Sensors
Durable, waterproof concrete sensors that monitor the environmental conditions within the concrete as it hardens. Models are available for both temperature and relative humidity monitoring.
4" Lightweight Retainer Rings (2)
CA-0200-L
Location: Unbonded Capping (Retainers and Pad Caps)
Aluminum retainer rings are 35% lighter than steel caps to reduce fatigue. They are heat-treated and hard anodized for longer wear and durability and conform to ASTM C-1231 specifications.
(6) options
Location: Sample Tins
Test Mark Industries supplies sample tins as part of a complete line of soil testing equipment.
(5) options
Location: Yield Buckets
Steel yield buckets from Test Mark are used for determining the unit weight of aggregate for concrete.
(4) options
Location: Tamping Rods for Concrete
Tamping rods from Test Mark eliminate air voids in concrete when making slump tests, concrete cylinders or conducting concrete air entrainment test.
SA-0210
Location: Sand Density
The Density Plate provides a flat, stable base for the sand cone apparatus - available from Test Mark Industries.
CA-0933
Location: Specimen Curing
The curing tank immersion heater from Test Mark has an adjustable thermostat and a 1,000 watt 15 amp incolloy shielded heating element that resists rust.
